The right choice of laminate

If you decide to replace the floor, then you need to choose the right materials. At the moment, linoleum has confidently replaced laminatewhich is of excellent quality.

Do you need instructions "Laying laminate with your own hands - a step-by-step guide with photos"?

Experts are always ready to give advice on how to choose and lay the material correctly. When choosing a material, the following factors should be considered:

• The type of space you are purchasing coverage for.
• Wear resistance of laminate.
• The ability to absorb water.
• The thickness of the boards, which are presented in a wide range.
• A manufacturer that offers building materials.

You should purchase laminate in special stores that are always ready to provide comprehensive advice and answer your questions. Naturally, the material intended for the hallway will differ from the thickness of the boards used for the bedroom.

back to index ↑

Proper preparation of the base for laminate flooring

This material has gained well-deserved popularity, because it has a low cost, and it is also quite easy to fit on its own. You need to follow the correct procedure in order to achieve the desired result.

You will need to do the following:

• The purchased laminate should be placed in the rooms where it will be installed. Do not open the packaging, the material must be acclimatized. You should leave the laminate for about 2 days to get used to the operating temperature. You will protect the wood from subsequent deformation.

• The floor should be thoroughly cleaned to remove dust. It is necessary to pre-vacuum the surface intended for laying the laminate.
• Waterproofing needs to be installed. For this stage, a film made of polyethylene is required. Laying is carried out directly on the floor, it is necessary to launch on the wall about 4 cm. When laying the strips, an overlap of about 15 cm is used, all joints must be glued with adhesive tape.

• Next, you need to lay the substrate. This stage will level the surface of the floor, make it even and smooth. Substrate thickness approx. 3 mm, laying directly on the waterproofing film. The substrate is laid without allowances, and the joints must be fastened with adhesive tape.

Special attention should be paid to the preparation of the base. This stage is designed to ensure that the floor is perfectly aligned. You will ensure maximum floor strength, which will significantly increase the service life.

Do not neglect the acclimatization period. If you start laying an unprepared laminate, deformation will occur. Soon you will have to completely change the coating, which will lead to high costs.

back to index ↑

Correct laying of the first row of laminate

The closest attention is paid to the procedure associated with laying the very first row. The quality of the whole process depends on the correctness of the work. Therefore, you need to be very careful about this stage.

You should do the following:

• Lay the first board. The laying process starts from the left corner. This solution allows you to correctly position the locks, which will greatly facilitate the further fastening of the laminate strips.

• The second stage is the placement of special spacers, which are placed between the wall and the strips of laminate. Such items can be purchased at a hardware store. However, it is quite simple to make wedges yourself. Enough to use 5-6 pieces.

• The next board is laid, which should be inserted into the lock of the first strip, an angle of 45 degrees is used. When the engagement has occurred, the board is lowered.

• The next laminate board is laid in the same way. You need to make sure that all the boards are properly connected.

• We lay the entire first row to the end.

When the laying of the first row is completed, you should proceed to the next step. Laying the second row also has its own characteristics.

back to index ↑

Laying the second layer of laminate

You are moving on to the next stage of work. Specialists identify the following tasks:

• A standard laminate board needs to be cut to stagger the stripes in relation to the strips in the first row.

• Take a block of wood in your left hand, which you need to attach to the wall. With the right hand, using a hammer, you need to knock out the bar to a position that will ensure tight fixation with the first row.

• The grooves of the boards of the second row should be tightly fixed with the grooves of the boards placed in the first row.
• Make sure there are no gaps between the laminate boards.
• Next, we continue to lay the strips of laminate, ensuring reliable engagement of the locks. The process continues until the end of the length of the second row.

• Be sure to once again make sure that the laminate strips are tightly adjacent to each other. Gaps, as well as gaps or breaks, are unacceptable; all connections must be tight and reliable.

After laying the second row, you should continue laying out the boards throughout the floor. Each next row is laid similarly to the second. You need to make sure that all bands are securely fixed.

Each engagement must be tight and secure. This solution will allow you to get a design designed for long-term use. Do-it-yourself laminate flooring - step by step guide with photos will allow you to learn how to lay popular material on your own.

back to index ↑

The final stage of laying the laminate

You have completed the laying of the laminate rows step by step. It's time to lay the last row. At this stage, quite often there is a problem associated with the fact that there is a place left for which the width of the board is too large.

Need to reduce the standard length as well as the width of the purchased strip? You can solve this issue yourself by using a jigsaw that runs on electricity.

At this stage, a standard strip of laminate is cut to ensure a perfect fit to the wall and other strips.

You need to accurately measure the floor to make it perfectly flat. If you cut too large a piece, then an unacceptable gap will appear.

When all tasks are completed, you need to remove the spacers that were located throughout the work site. Laminate work completed. It remains to proceed to the stage associated with the execution of the finishing.

You need to decorate the room with skirting boards and thresholds. They must be carefully sized. If at the moment there are small roughnesses, then they can be masked.

In specialized stores, there are crayons that are designed to putty on laminate scuffs. In construction centers you can find such an element that is quite inexpensive.

back to index ↑

Laminate is the perfect flooring for any space.

At the moment, laminate flooring is successfully used both for flooring in city apartments, and in private homes and offices. This material has a different thickness, so you can choose the best quality solution.

If you are interested in the design of the hallway or kitchen, then you should give preference to darker colors. Do not save on the cost of boards. It is best to purchase a laminate that has a greater thickness. Such material is characterized by excellent wear resistance, easily adapts to temperature changes.

Sufficient width allows for continuous wet cleaning. Laminate has excellent moisture resistance. Manufacturers offer a huge selection of laminate thicknesses, as well as various color schemes.

back to index ↑

Laying laminate flooring on concrete floors

You need to pay special attention to the preparatory stage. If you are going to install laminate flooring in a new home, you should wait until the fresh concrete mix is ​​completely cured.

If laying is carried out on an old base, it may be necessary to pre-level the surface. You must be sure to remove all chips, cracks and bumps. Only after that it will be possible to start laying the laminate.

The requirements for the foundation are as follows:

• Perfect evenness must be ensured.
• Moisture protection is required.
• Good thermal insulation is required.
• Noise protection needs to be provided.

The procedure associated with laying the laminate can only be started when the preparatory work has been carefully carried out. If you neglect this stage, then you will not be able to get the desired result. Soon you will have to start replacing the coating again.

back to index ↑

Laying laminate flooring on wood floors

The surface should be carefully prepared, it should be perfectly flat and smooth. You should pre-clean the surface before you start laying the insulating layer.

If the surface is not prepared carefully enough, this will cause the following negative consequences:

• The lock system is damaged, which is particularly sensitive.
• The grooves begin to loosen, which leads to the breakage of the ridges, which are quite fragile.

Incorrect preparation of the wooden base will cause additional costs, because soon you will have to completely re-lay the laminate.

back to index ↑

Scheduling work related to laying laminate flooring

In order to get the perfect solution, you need to properly plan all your actions. Initially, you will need to calculate the amount of material needed. You need to determine the dimensions of the room, you will need accurate measurements of the width and height.

Next, you should find out the dimensions of each strip of laminate. You can make a special drawing to outline the layout of the boards. This solution will allow you to purchase the required amount of material without overpaying for unnecessary strips.

Naturally, you will be laying the laminate in a checkerboard pattern, so you should calculate how many pieces one plank will be cut into. Will there be small pieces of laminate left? They can be used to make spacers so you don't have to buy them separately at the store.

Careful planning will allow you to reap the following benefits:

• Purchase the required amount of material, which will insure against the need to urgently buy a few strips.
• You will draw up an exact scheme that will facilitate the procedure for laying the laminate with your own hands.
• You will know exactly in what order to lay the laminate flooring, which will significantly speed up the work.

You should also purchase a film in advance, which will be required for insulation and a substrate. If you pre-prepare all the materials and tools, then do-it-yourself laminate flooring - a step-by-step guide with photos will allow you to complete the procedure efficiently and effectively.

back to index ↑

Benefits of installing laminate

In every room, the floor must be reliable. Therefore, if a creak is constantly heard under your feet, and the structure bends, then it makes sense to replace the coating.

One popular solution is laminate flooring. The main advantages of this material are:

• Low cost, which is acceptable for any client.
• Laminate is available in a huge variety of colors, so you can always choose the most harmonious solution.

• The material is of excellent quality, designed for long-term use.
• You can lay the floor yourself, you don’t even need special tools.

Presented instruction do-it-yourself laminate flooring - step by step guide with photos will allow you to quickly replace the floors in a separate room, as well as throughout the apartment or house.

You can choose a solution for parquet, which looks especially beautiful in the living room, hall or hall. For the corridor and the kitchen, extra-strong boards are offered that are ready to withstand heavy loads.

back to index ↑

How to transform a room with laminate

If you want to update the atmosphere in a private house or a city apartment, then laying a laminate floor will be a great solution. Is there linoleum at the moment and the floor has a concrete base?

You should do the following:

1. You need to completely remove the linoleum.

2. Completely clean the base, the presence of drops is unacceptable.

3. The surface must be completely level.

4. The purchased laminate should lie down in the room for about 2 days to get used to the operating temperature.

5. It is necessary to lay a layer of insulation, as well as a substrate according to the established scheme.

6. You can start laying the laminate.

If you do not want to throw out the old linoleum, then experts recommend using it as a substrate, which will save on the purchase of special material.

You can decorate the entire apartment in the same style by purchasing a laminate of the same color. Want to get variety? A huge selection allows you to decorate each room in your own style.

For entrance and kitchen areas, as a rule, darker and more durable options are purchased. In the living room and bedroom, you can show your imagination by applying light colors of the coating.

Laminate is effectively combined with plastic or wooden type windows. You can choose a color that perfectly harmonizes with the created interior. If necessary, you can contact the designer, who will suggest the most profitable solution.

back to index ↑

Benefits of DIY laminate flooring

If you started a repair, then anyone can replace the flooring. This process is quite simple. Instructions for laying laminate with your own hands will come to the rescue - a step-by-step guide with photos.

Need to choose the right laminate? Experienced salespeople are always ready to help. They will tell you what material is best to purchase for a particular room.

In one and the same place you can buy all the necessary materials for the successful completion of the work. If you decide to change the coating in all rooms, then it makes sense to purchase laminate in those places where discounts are provided for a large number of goods.

Laying laminate flooring yourself will give you the following benefits:

• You will save money that you need to pay the masters.
• You yourself will ensure the high quality of laying the material.
• Independent work will make sure that each stage of the work is completed.
• You will get the opportunity to get a coating designed for long-term use.
• You will be able to independently plan the rhythm of work, which will allow you to completely lay the material in a short time.
• You can start working at any time.

Working independently is always fun. You can immediately see the result of your work. Laying laminate does not require the purchase of special tools, which is quite convenient.

However, if you work a lot, then it makes sense to turn to specialists. They will be able to lay the laminate in accordance with the requirements. Now you know how the process should go, so you can always control the work of the wizards.

back to index ↑

Important steps for laying laminate with your own hands

Before you start buying material, you should study the main selection criteria. You need to know which laminate is right for your space. Be sure to take accurate measurements to correctly calculate the number of boards needed.

When you go to the store, take a list with you:

• The required amount of laminate to be installed.
• Required amount of film and substrate.

You can purchase all the necessary materials on the Internet, which is quite convenient. As a rule, the goods are sold from a warehouse, have a quality guarantee. Many companies offer free shipping.

Do not forget that the laying process can only be started after 2 days, the laminate must acclimatize.Pay special attention to cleaning the surface, pre-leveling the floor. It is unacceptable to leave holes and roughness. The duration of the operation of the coating depends on the quality of this work.

Make sure that the strips fit snugly together, do not leave gaps. During operation, this will negatively affect the period of use of the laminate. Each step must be done carefully.

Do-it-yourself laminate laying instructions will come to the rescue - a step-by-step guide with photos that will allow you to completely replace the floor covering. You will have the skills to get the job done quickly and efficiently. It is required to follow a certain technology in order to achieve the desired result.

back to index ↑

Video

 

 

---