Floors in the bathroom must always be resistant to high humidity, otherwise their service life will be minimal, and aesthetic qualities will be lost in the first days of use.
If we talk about the most common option, then most of the floors in the bathrooms are tiled, as this material has a low cost and at the same time perfectly resists high humidity. Nowadays, the wooden floor in this room should no longer surprise anyone, as this is a common practice.
Wooden floor in the bathroom
From an aesthetic point of view, such a solution will look attractive, but many are also concerned about the technical component of this issue. It is important to immediately remember that it is from natural wood that baths are built, so that moisture resistance can be fought. Today we will consider the question of how this natural material can be effectively applied at the stage of finishing the floor area in the bathroom.
back to index ↑Wooden floor in the bathroom - how possible?
Wood is a natural and harmless material that needs no special introduction. Many finish the floors in the bathroom for them solely because this solution makes it possible to achieve maximum comfort.
The wooden floor in the bathroom will provide maximum comfort
All objects located in this room will always have approximately the same temperature, which is important. It is known that the peculiarity of tile is that it constantly remains cold, so you always have to use numerous rugs or do forced floor heating. As for the wooden floor, it is completely devoid of this drawback and has long been positioned as energy-saving.
Wooden floor is warmer than tile
By choosing this option, it will be possible to significantly save on electricity and at the same time make the room as comfortable as possible. If you are a fan of unusual solutions at the stage of interior design, you can combine natural wood with other materials to achieve unusual results.
back to index ↑How to choose a tree type?
It is important to note that for many centuries it was wood that was used to build ships, so it makes no sense to say that it is impossible to make a floor in a room with high humidity. In many ways, the durability of the innovative flooring in the future will depend on what kind of wood you will use. Of course, it is important to choose the one that can be exposed to high humidity for a long time. Most often, the floors in these rooms are made of teak, as this variety has an unprecedented high density and can withstand moisture 100% without special treatment. At the installation stage, you still have to follow certain rules so that the coating can maintain its functional and aesthetic qualities for several decades.
Teak floor resists moisture without special treatment
The first thing you need to pay attention to is the joints between all the boards. They must be sealed with appropriate sealants. To achieve the best result, it is advisable to use ship analogs, since in the end it will be possible to create a coating that will not absorb moisture during operation and will not yield to tiles in any way. There is only one drawback of teak - a rather high cost.
All joints between boards must be carefully sealed with sealant.
If it is not possible to use it, then it does not matter, because there is an analogue - larch. The main feature of the material is that it is very durable, and also not affected by moisture. For many years, it has been actively used in the construction of ships, as well as supports for bridges. There are other options when you do not have to spend a lot of money. For example, oak, ash or elm. Often the floors in this room are finished with cork, as it has a low cost and is environmentally friendly.
Larch bathroom floor
Please note that it is strictly the base of the coating that is made from cork, that is, it is first crushed, and only after that it is pressed at high temperatures. As for the upper part of the coating, it is sometimes made of the same material, but veneer or vinyl can be used. Such a floor will not be afraid of high humidity, so it can be safely installed in bathrooms.
Cork flooring is moisture resistant
It also makes sense to use thermal wood as a finishing material - an innovative material that has recently appeared on the market, but managed to prove itself perfectly in different countries of the world. It is made by the method of steam treatment of wood at a temperature of more than two hundred degrees, but the main condition is the complete absence of contact with oxygen. As a result, it is possible to obtain a material that, under the influence of high humidity, will not deform and absorb water. Another advantage of this option is that this coating is not affected by fungi.
Thermowood is not affected by fungi
Mounting Features
If you decide to install a wooden floor in your bathroom, you need to follow certain rules, which will be discussed below. Work should begin with the preparatory stage. Any material must be mounted on a properly prepared surface. It should be checked that it is strictly geometrically even and does not have any significant defects. A number of requirements are invariably presented to the basic foundation and they must be taken into account. The floor should be as even as possible, and the differences should not exceed one millimeter.
The floor must be leveled before laying wood.
As for the screed, it must always be extremely strong, since during operation it will have to take on very significant loads. The density should be strictly uniform over the entire floor area, and there should be no chips. At the stage of formation of the base, you can use not only a cement screed, but also a number of other products. For example, the most common moisture-resistant plywood is perfect for solving this issue.
Moisture resistant plywood for floor underlay
It happens that it is necessary to ensure maximum thermal insulation of the floor area and for this you should use the appropriate materials. There are a lot of heaters on the construction market, so choosing the best option is not difficult. The main thing is that these materials do not change their characteristics under the influence of high humidity.
Waterproofing should also be given special attention.If you decide to insulate the floor, then you need to apply waterproofing materials. After the base is completely leveled, you can begin to perform this work. You can use roll materials or mastics, which are sold already in a ready-to-use state. It is important to place the material so that it also covers the lower part of the walls. A gap of ten centimeters is enough to achieve the desired result. A number of waterproofing mastics should also be used, which are applied in several layers with a construction brush.
Sealant flooring in the bathroom
When this work is completed, we recommend applying a good layer of soil, and only after that you can begin to mount the boards.
It is strongly recommended that even the highest quality material from eminent manufacturers be kept in a special room before installation, subject to a constant temperature, so that it kind of “acclimatizes” and is ready for full-fledged further use.
At the initial stage of laying the finishing material, it is necessary to make markings using a special tool. It is not advisable to rush, because you need to complete this step with maximum accuracy. Do not forget to mark the locations of all kinds of communications in order to protect yourself from unnecessary work in the future. As a rule, laying begins in the direction from the door to the far wall. In many ways, the laying technology will depend on what kind of material you decide to use.
Bathroom wood flooring
When installation work is completed, visually inspect the surface and identify defects. If they are still found, it is recommended to immediately repair chips and cracks with special mastics. As you already understood, natural wood floors can be installed in rooms where high humidity is invariably observed. There are many materials that are not afraid of this circumstance and can last for a long time. If you properly choose the material for finishing and at the same time mount it with high quality, then for a long time you will not have to redo the floors.
back to index ↑About aesthetic qualities
Wood floors attract attention with their beauty. It is known that each individual tree has a certain structure and pattern of fibers. It cannot be repeated and it is this uniqueness that captivates all connoisseurs of original interiors.
Wooden floor will make the interior of the bathroom unique
It is not easy to install such material on your own, but if you take into account all the recommendations provided in this article, then it will not be so difficult to complete the work. You can talk about the color of the flooring for a long time, but you need to take into account the main interior of the room. If the bathroom is already decorated in a certain style, then the floors should be made in the appropriate style. Oak plank, for example, is dark in color and has a distinct grain pattern. If you choose a cork tree, then the floor area will be lighter. There are many options, and if you give preference to a thermal tree, then an endless scope opens up for the implementation of the most daring ideas.
The color of the wooden floor in the bathroom should be combined with the interior
Summing up
Currently, many still finish the floors in rooms with high humidity through tile and ceramic tiles. As for wood, this option repels many, because it seems short-lived and expensive. In fact, the situation is different and you will not have to burden yourself with significant expenses for the purchase of finishing material. A tile may also have a high price, but retain the standard characteristics.If you do not want to overpay, then you can simply choose a cheaper natural material, fortunately, it is presented in a wide range on the modern construction market.
Thanks to the large assortment, it will not be difficult to find the right wood
It is recommended to trust the installation work to qualified professionals, because if you make a mistake that is insignificant at first glance, everything will go down the drain, and the floor covering will soon become unusable.
Use only high-quality materials for the floor in the bathroom
It is important to use quality material, as well as mastics, to protect the wood from moisture penetration. You can realize any of your design ideas through the use of this material and at the same time not spend a lot of time or effort on the implementation of your plans. Contact the professionals, and they will install a floor covering that can last for decades in a short time.
back to index ↑Photo gallery - wooden floor in the bathroom
